Booming home renovation market has driven the production and sale of decorative plaster products, and is widely used in the production of all kinds of plaster mold industry, will also be given a better opportunity for development, industrialization and development settled gradually on the rise, and then the merits of varying plaster mold has gradually become a stumbling block to restrict the entire industry, the paper currently plaster mold of advanced production technology of representatives Star Ocean mold, for example, explain plaster mold releasing major questions about aspects of the production . Plaster mold releasing segment mold quality is an important factor in the decision, either to protect the accuracy of mold products in the above requirements, and can achieve high-end positioning of the principle of product quality level, the release of the application is in plaster molds After the processes, the first step should be sufficient to ensure the plaster has been drained to the base standard, plaster mold wholesale, Star Ocean mold think this is the smooth completion of the release part of the premise, Shaanxi plaster mold, if the application of gypsum and did not meet certain criteria, it will bring damage to the back of the mold, the release can not be successfully completed. The second step will be gypsum placed on the ground, and maintain a certain flatness, can not occur shake other issues affecting the stripping, and then remove the rack with both hands to slowly peel the mold from the bottom, in this part of the summary must be noted yes, pay attention to mold his hands deep inside were slowly to complete the release, if you encounter a certain amount of bonding sites and complex parts can not be successfully completed, you can choose the mold surface pour some boiling water to make mold softened after gently off mode. Third, when the plaster mold releasing sure to keep a good attitude and skilled, both of which are needed in the long-term culture gradually built up, especially for Star Ocean mold it, often need to deal with some of the more complex customized mold parts, and this is often more difficult, and in many cases have to take some special treatment in order to ultimately achieve a smooth stripping plaster mold. Yi Cai cartoon craft die? /? 2012-02-27? [Big]? [In]? [Small] plaster white embryo is produced using plaster molds, plaster mold is how to make out of it, the first major plaster mold material is divided into two, one is rubber material, and the other is natural latex material. Two materials different production methods is not the same decision: Cai Yi introduces rubber mold plaster mold production methods, rubber plaster mold production method is to emphasize good raw materials --- --- warm mother die then brush coated --- brush after brushing mother die? mother die and then bake in the oven (200 degrees oven temperature control) ---- baked after the first pass? --- recapture oven painted again, repeat This action 3-4 times, grilled mold shiny appearance, product toughness usual. When the master is burned Shousheng phenomenon. Natural latex plaster mold baking methods: a good tune material master mold --- --- clean with a brush evenly brushing aside the mother die of natural air-dry --- --- --- this is repeated 10 times and then painted a good mother die on a heated indoor (temperature about 40 degrees) --- 5-10 days to the mold; produced by mold super toughness, inner texture clear, strong and durable. Yi Cai cartoon craft die? /? 2012-02-27? [Big]? [In]? [Small] plaster white embryo is produced using plaster molds, plaster mold is how to make out of it, the first major plaster mold material is divided into two, one is rubber material, plaster mold factory, the other is a natural latex material. Two materials different production methods is not the same decision: Cai Yi introduces rubber mold plaster mold production methods, rubber plaster mold production methods, the wholesale plaster mold, to emphasize good raw materials --- warm mother die - -? then brush brushing mother die --- mother die after brushing the oven and then bake (oven temperature control 200 degrees) ---- --- After the first pass and then baked again painted? put the oven, repeat this action 3-4 times, grilled mold shiny appearance, product toughness usual. When the master is burned Shousheng phenomenon. Natural latex plaster mold baking methods: a good tune material master mold --- --- clean with a brush evenly brushing aside the mother die of natural air-dry --- --- --- this is repeated 10 times and then painted a good mother die on a heated indoor (temperature about 40 degrees) --- 5-10 days to the mold; produced by mold super toughness, inner texture clear, strong and durable. Shaanxi plaster mold | ARTEL plaster mold | Aluminum plaster mold by Gaomi Artel plaster mold factory. Shaanxi plaster mold | ARTEL plaster mold | Aluminum plaster mold is Gaomi Artel plaster mold factory (www.htsgmj.com) (www.htsgmj.com) this year introduced a new upgrade, the above picture is for reference only, please call Tel This page or image on to obtain the latest information, contact: Du Jingli.